ldc-2 ldc model ldc15f-1 LDC15F-2 dc output v1 +5v 2.0 ( peak 3.0 ) a +5v 2.0 ( peak 3.0 ) a v2 +12v 0.3 ( peak 0.6 ) a +15v 0.3 ( peak 0.6 ) a v3 -12v 0.2 ( peak 0.3 ) a -15v 0.2 ( peak 0.3 ) a specifications model ldc15f-1 LDC15F-2 input voltage[v] ac85 - 264 1 f or dc110 - 370 current[a] acin 100v 0.4typ ( io=100% ) frequency[hz] 47 - 440 or dc efficiency[%] acin 100v 70typ ( io=100% ) inrush current[a] acin 100v 25typ ( io=100% ) acin 200v 50typ ( io=100% ) leakage current[ma] 0.75max ( 60hz , according to ul , csa , vde and den-an ) output voltage[v] +5 +12 -12 +5 +15 -15 current[a] * 1 0 - 2.0 ( peak 3.0 ) 0 - 0.3 ( peak 0.6 ) 0 - 0.2 ( peak 0.3 ) 0 - 2.0 ( peak 3.0 ) 0 - 0.3 ( peak 0.6 ) 0 - 0.2 ( peak 0.3 ) line regulation[mv] 20max 48max 48max 20max 60max 60max load regulation[mv] 100max 120max 120max 100max 150max 150max ripple[mvp-p] 0to+50 c * 2 100max 120max 120max 100max 120max 120max -10-0 c * 2 140max 160max 160max 140max 160max 160max ripple noise[mvp-p] 0to+50 c * 2 120max 150max 150max 120max 150max 150max -10-0 c * 2 160max 180max 180max 160max 180max 180max temperature regulation[mv] 0to+50 c 50max 350max 350max 50max 350max 350max -10 to +50 c 60max 420max 420max 60max 420max 420max drift[mv] * 3 20max xx xx 20max xx xx start-up time[ms] 100max ( acin 85v , io=100% ) hold-up time[ms] 10typ ( acin 85v , io=100% ), 20typ ( acin 100v , io=100% ), 100typ ( acin 200v , io=100% ) output voltage adjustment range[v] fixed fixed fixed fixed fixed fixed output voltage setting[v] 4.9 to 5.3 11.4 to 12.6 -11.4 to -12.6 4.9 to 5.3 14.25 to 15.75 -14.25 to -15.75 protection circuit and others overcurrent protection works over 105% of rating and recovers automatically overvoltage protection works over 115% of rating by zener diode clamping ( +5v only ) operating indication not provided remote sensing not provided remote on/off not provided isolation input-output ac3 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) input-fg ac2 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) output-fg ac500v 1minute , cutoff current = 100ma , dc500v 50m w min ( at room temperature ) output-output ( v1-v2 , v3 ) ac100v 1minute , cutoff current = 100ma , dc100v 10m w min ( at room temperature ) environment operating temp. , humid.and altitude -10 to +60 c , 20 - 90%rh ( non condensing )( refer to derating curve ), 3 , 000m ( 10 , 000feet ) storage temp. , humid.and altitude -20 to +75 c , 20 - 90%rh ( non condensing ), 9 , 000m ( 30 , 000feet ) vibration 10 - 55hz , 19.6m/s 2 ( 2g ), 3minutes period , 60minutes each along x , y and z axis impact 196.1m/s 2 ( 20g ), 11ms , once each x , y and z axis safety and noise regulations agency approvals ul60950-1 , en60950-1 , en50178 , csa c22.2 no.60950-1 complies with den-an and iec60950-1 conducted noise complies with fcc-b , cispr22-b , en55022-b , vcci-b others case size/weight 50 x 26 x 127mm [ 1.97 x 1.02 x 5 inches ] ( w x h x d ) /150g max ( without chassis and cover ) cooling method convection * 1 peak load for 10sec. or less is acceptable if the total wattage is less than the rated wattage(-1: 16w, -2: 17.5w).when the loa d of +5v is oa, other output can be drawn by 80% of rated current. * 2 measured by 20mhz oscilloscope or ripple-noise meter (equivalent to keisoku-giken:rm101). * 3 drift is the change in dc output for an eight hour period after a half-hour warm-up at 25 c with the input voltage held constant at the rated input/output. * 4 please contact us about safety approvals for the model with option. * avoid prolonged use under over-load. * derating is required when operated with chassis and cover. ldc15f ac-dc power supplies open frame/enclosed type ld c 15 f -1 - o ordering information 1 series name 2 multiple output 3 output wattage 4 universal input 5 output voltage combina- tion 6 optional * 4 c :with coating g :low leakage current s :with chassis sn :with chassis & cover y :with potentiometer r 123456 - % $ @ & j o e e - % $ - % $ & j o e e - % $
ldc-3 ldc ? derating curve ? overcurrent characteristics ( ldc15f-1 ) ? rise time & fall time ( ldc15f-1 ) ? static characteristics ( ldc15f-1 ) ldc15f external view ? weight: 150g max(without chassis and cover) ? tolerance: t 1[ t 0.04] ? dimensions in mm,[ ]=inches ? pcb material: glass composite(cem3) ? chassis and cover is optional. ? mounting torque: 0.6nm(6.3kgfcm)max 4- f 3.5 [ 0.14 ] f 3.5 [ 0.14 ] 50 [ 1.97 ] 57 [ 2.24 ] 28.5 [ 1.12 ] 23 [ 0.91 ] 127 [ 5 ] 147 [ 5.79 ] 19 [ 0.95 ] pcb t=1.6 [ 0.06 ] 3.5 [ 0.14 ] 3.5 [ 0.14 ] 3.5 [ 0.14 ] 3 max [ 0.12 ] 3.5 [ 0.14 ] 10 [ 0.39 ] 19 [ 0.75 ] 38 [ 1.50 ] 6 [ 0.24 ] 6 [ 0.24 ] 15 [ 0.59 ] f 3.5 [ 0.14 ] 4.75 [ 0.19 ] 43 0.5 [ 1.69 ] 120 0.5 [ 4.72 ] 135 0.5 [ 5.31 ] 135 0.5 [ 5.31 ] 25 0.5 [ 0.98 ] performance data - % $ @ & j o e e - % $ - % $ & j o e e - % $
ldc-4 ldc model ldc30f-1 ldc30f-2 dc output v1 +5v 3.0 ( peak 4.5 ) a +5v 3.0 ( peak 4.5 ) a v2 +12v 1.2 ( peak 2.0 ) a +15v 1.0 ( peak 2.0 ) a v3 -12v 0.3 ( peak 0.45 ) a -15v 0.3 ( peak 0.45 ) a specifications model ldc30f-1 ldc30f-2 input voltage[v] ac85 - 264 1 f or dc110 - 370 current[a] acin 100v 0.8typ ( io=100% ) frequency[hz] 47 - 440 or dc efficiency[%] acin 100v 72typ ( io=100% ) inrush current[a] acin 100v 25typ ( io=100% )( at cold start ) acin 200v 50typ ( io=100% )( at cold start ) leakage current[ma] 0.75max ( 60hz , according to ul , csa , vde and den-an ) output voltage[v] +5 +12 -12 +5 +15 -15 current[a] * 1 0 - 3.0 ( peak 4.5 ) 0 - 1.2 ( peak 2.0 ) 0 - 0.3 ( peak 0.45 ) 0 - 3.0 ( peak 4.5 ) 0 - 1.0 ( peak 2.0 ) 0 - 0.3 ( peak 0.45 ) line regulation[mv] 20max 48max 48max 20max 60max 60max load regulation[mv] 100max 120max 150max 100max 120max 150max ripple[mvp-p] 0to+50 c * 2 100max 120max 120max 100max 120max 120max -10-0 c * 2 150max 160max 160max 150max 160max 160max ripple noise[mvp-p] 0to+50 c * 2 120max 150max 150max 120max 150max 150max -10-0 c * 2 170max 180max 180max 170max 180max 180max temperature regulation[mv] 0to+50 c 50max 350max 350max 50max 350max 350max -10 to +50 c 60max 420max 420max 60max 420max 420max drift[mv] * 3 20max xx xx 20max xx xx start-up time[ms] 100max ( acin 85v , io=100% ) hold-up time[ms] 10typ ( acin 85v , io=100% ), 20typ ( acin 100v , io=100% ), 100typ ( acin 200v , io=100% ) output voltage adjustment range[v] fixed fixed fixed fixed fixed fixed output voltage setting[v] 4.9 to 5.3 11.4 to 12.6 -11.4 to -12.6 4.9 to 5.3 14.25 to 15.75 -14.25 to -15.75 protection circuit and others overcurrent protection works over 105% of rating and recovers automatically overvoltage protection works at 115 - 140% of rating ( +5v only ) operating indication not provided remote sensing not provided remote on/off not provided isolation input-output ac3 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) input-fg ac2 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) output-fg ac500v 1minute , cutoff current = 100ma , dc500v 50m w min ( at room temperature ) output-output ( v1-v2 , v3 ) ac100v 1minute , cutoff current = 100ma , dc100v 10m w min ( at room temperature ) environment operating temp. , humid.and altitude -10 to +60 c , 20 - 90%rh ( non condensing )( refer to derating curve ), 3 , 000m ( 10 , 000feet ) storage temp. , humid.and altitude -20 to +75 c , 20 - 90%rh ( non condensing ), 9 , 000m ( 30 , 000feet ) vibration 10 - 55hz , 19.6m/s 2 ( 2g ), 3minutes period , 60minutes each along x , y and z axis impact 196.1m/s 2 ( 20g ), 11ms , once each x , y and z axis safety and noise regulations agency approvals ul60950-1 , en60950-1 , en50178 , csa c22.2 no.60950-1 complies with den-an and iec60950-1 conducted noise complies with fcc-b , cispr22-b , en55022-b , vcci-b others case size/weight 65 x 26 x 140mm [ 2.56 x 1.02 x 5.51 inches ] ( w x h x d ) / 220g max ( without chassis and cover ) cooling method convection * 1 peak load for 10sec. or less is acceptable if the total wattage is less than the rated wattage(-1: 33w, -2: 34.5w).when the loa d of +5v is oa, other output can be drawn by 80% of rated current. * 2 measured by 20mhz oscilloscope or ripple-noise meter (equivalent to keisoku-giken:rm101). * 3 drift is the change in dc output for an eight hour period after a half-hour warm-up at 25 c with the input voltage held constant at the rated input/output. * 4 please contact us about safety approvals for the model with option. * avoid prolonged use under over-load. * derating is required when operated with chassis and cover. ldc30f ac-dc power supplies open frame/enclosed type ld c 30 f -1 - o ordering information 1 series name 2 multiple output 3 output wattage 4 universal input 5 output voltage combina- tion 6 optional * 4 c :with coating g :low leakage current s :with chassis sn :with chassis & cover y :with potentiometer r 123456 - % $ @ & j o e e - % $ - % $ & j o e e - % $
ldc-5 ldc ? derating curve ? overcurrent characteristics ( ldc30f-1 ) ? rise time & fall time ( ldc30f-1 ) ? static characteristics ( ldc30f-1 ) ldc30f external view ? weight: 220g max(without chassis and cover) ? tolerance: t 1[ t 0.04] ? dimensions in mm,[ ]=inches ? pcb material: glass composite(cem3) ? chassis and cover is optional. ? mounting torque: 0.6nm(6.3kgfcm)max 4- f 3.5 [ 0.14 ] f 3.5 [ 0.14 ] 65 [ 2.56 ] 72 [ 2.83 ] 36 [ 1.42 ] 23 [ 0.91 ] 140 [ 5.51 ] 160 [ 6.30 ] 57.5 [ 2.26 ] pcb t=1.6 [ 0.06 ] 4 [ 0.16 ] 3.5 [ 0.14 ] 3.5 [ 0.14 ] 3 max [ 0.12 ] 4 [ 0.16 ] 10 [ 0.39 ] 19 [ 0.75 ] 38 [ 1.50 ] 5 [ 0.20 ] 5 [ 0.20 ] 26 [ 1.02 ] 2- f 3.5 [ 0.14 ] 9.25 [ 0.36 ] 57 0.5 [ 2.24 ] 132 0.5 [ 5.20 ] 150 0.5 [ 5.91 ] 150 0.5 [ 5.91 ] 20 0.5 [ 0.79 ] 16 [ 0.63 ] 40 0.5 [ 1.57 ] performance data - % $ @ & j o e e - % $ - % $ & j o e e - % $
ldc-6 ldc model ldc60f-1 ldc60f-2 dc output v1 +5v 5.0 ( peak 7.0 ) a +5v 5.0 ( peak 7.0 ) a v2 +12v 2.5 ( peak 3.5 ) a +15v 2.0 ( peak 3.5 ) a v3 -12v 0.5 ( peak 0.7 ) a -15v 0.5 ( peak 0.7 ) a specifications model ldc60f-1 ldc60f-2 input voltage[v] ac85 - 264 1 f or dc110 - 370 current[a] acin 100v 1.4typ ( io=100% ) frequency[hz] 47 - 440 or dc efficiency[%] acin 100v 72typ ( io=100% ) inrush current[a] acin 100v 30typ ( io=100% )( at cold start ) acin 200v 60typ ( io=100% )( at cold start ) leakage current[ma] 0.75max ( 60hz , according to ul , csa , vde and den-an ) output voltage[v] +5 +12 -12 +5 +15 -15 current[a] * 1 0 - 5.0 ( peak 7.0 ) 0 - 2.5 ( peak 3.5 ) 0 - 0.5 ( peak 0.7 ) 0 - 5.0 ( peak 7.0 ) 0 - 2.0 ( peak 3.5 ) 0 - 0.5 ( peak 0.7 ) line regulation[mv] 20max 48max 48max 20max 60max 60max load regulation[mv] 100max 150max 150max 100max 150max 150max ripple[mvp-p] 0to+50 c * 2 100max 120max 120max 100max 120max 120max -10-0 c * 2 150max 160max 160max 150max 160max 160max ripple noise[mvp-p] 0to+50 c * 2 120max 150max 150max 120max 150max 150max -10-0 c * 2 170max 180max 180max 170max 180max 180max temperature regulation[mv] 0to+50 c 50max 350max 350max 50max 350max 350max -10 to +50 c 60max 420max 420max 60max 420max 420max drift[mv] * 3 20max xx xx 20max xx xx start-up time[ms] 200max ( acin 85v , io=100% ) hold-up time[ms] 10typ ( acin 85v , io=100% ), 20typ ( acin 100v , io=100% ), 100typ ( acin 200v , io=100% ) output voltage adjustment range[v] fixed fixed fixed fixed fixed fixed output voltage setting[v] 4.9 to 5.3 11.4 to 12.6 -11.4 to -12.6 4.9 to 5.3 14.25 to 15.75 -14.25 to -15.75 protection circuit and others overcurrent protection works over 105% of rating and recovers automatically overvoltage protection works over 115% of rating by zener diode clamping ( only available with v1 , v2 ) operating indication not provided remote sensing not provided remote on/off not provided isolation input-output ac3 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) input-fg ac2 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) output-fg ac500v 1minute , cutoff current = 100ma , dc500v 50m w min ( at room temperature ) output-output ( v1-v2 , v3 ) ac100v 1minute , cutoff current = 100ma , dc100v 10m w min ( at room temperature ) environment operating temp. , humid.and altitude -10 to +60 c , 20 - 90%rh ( non condensing )( refer to derating curve ), 3 , 000m ( 10 , 000feet ) storage temp. , humid.and altitude -20 to +75 c , 20 - 90%rh ( non condensing ), 9 , 000m ( 30 , 000feet ) vibration 10 - 55hz , 19.6m/s 2 ( 2g ), 3minutes period , 60minutes each along x , y and z axis impact 196.1m/s 2 ( 20g ), 11ms , once each x , y and z axis safety and noise regulations agency approvals ul60950-1 , en60950-1 , en50178 , csa c22.2 no.60950-1 complies with den-an and iec60950-1 conducted noise complies with fcc-b , cispr22-b , en55022-b , vcci-b others case size/weight 83 x 26 x 185mm [ 3.27 x 1.02 x 7.28 inches ] ( w x h x d ) / 300g max ( without chassis and cover ) cooling method convection * 1 peak load for 10sec. or less is acceptable if the total wattage is less than the rated wattage(-1: 61w, -2: 62.5w).when the loa d of +5v is oa, other output can be drawn by 80% of rated current. * 2 measured by 20mhz oscilloscope or ripple-noise meter (equivalent to keisoku-giken:rm101). * 3 drift is the change in dc output for an eight hour period after a half-hour warm-up at 25 c with the input voltage held constant at the rated input/output. * 4 please contact us about safety approvals for the model with option. * avoid prolonged use under over-load. * derating is required when operated with chassis and cover. ldc60f ac-dc power supplies open frame/enclosed type ld c 60 f -1 - o ordering information 1 series name 2 multiple output 3 output wattage 4 universal input 5 output voltage combina- tion 6 optional * 4 c :with coating g :low leakage current s :with chassis sn :with chassis & cover y :with potentiometer r 123456 - % $ @ & j o e e - % $ - % $ & j o e e - % $
ldc-7 ldc ? derating curve ? overcurrent characteristics ( ldc60f-1 ) ? rise time & fall time ( ldc60f-1 ) ? static characteristics ( ldc60f-1 ) ldc60f external view ? weight: 300g max(without chassis and cover) ? tolerance: t 1[ t 0.04] ? dimensions in mm,[ ]=inches ? pcb material: glass composite(cem3) ? chassis and cover is optional. ? mounting torque: 1.5nm(16kgfcm)max 5- f 3.5 [ 0.14 ] f 4.5 [ 0.18 ] 83 [ 3.27 ] 92 [ 3.62 ] 46 [ 1.81 ] 23 [ 0.91 ] 185 [ 7.28 ] 210 [ 8.27 ] 40.75 [ 1.60 ] pcb t=1.6 [ 0.06 ] 4 [ 0.16 ] 4.5 [ 0.18 ] 4.5 [ 0.18 ] 3 max [ 0.12 ] 4 [ 0.16 ] 11 [ 0.43 ] 19 [ 0.75 ] 38 [ 1.50 ] 7 [ 0.28 ] 7 [ 0.28 ] 31 [ 1.22 ] 2- f 4.5 [ 0.18 ] 8 [ 0.31 ] 39 0.5 [ 1.54 ] 75 0.5 [ 2.95 ] 111 0.5 [ 4.37 ] 177 0.5 [ 6.97 ] 195 0.5 [ 7.68 ] 195 0.5 [ 7.68 ] 30 0.5 [ 1.18 ] 21 [ 0.83 ] 50 0.5 [ 1.97 ] performance data - % $ @ & j o e e - % $ - % $ & j o e e - % $
|
